21 MM 5C Round Collet Reviews
21 MM 5C Round Collet Feature
- Round 5C collet to hold metric round tools or work.
Thursday, September 22, 2011
21 MM 5C Round Collet
Wednesday, September 21, 2011
Niagara Cutter SPC408 Cobalt Steel End Mill, General Purpose, TiCN Coated, 4 Flutes, Square End, 1/2" Cutting Length, 3/16" Cutting Diameter
Niagara Cutter SPC408 Cobalt Steel End Mill, General Purpose, TiCN Coated, 4 Flutes, Square End, 1/2" Cutting Length, 3/16" Cutting Diameter Reviews
Niagara Cutter SPC408 Cobalt Steel End Mill, General Purpose, TiCN Coated, 4 Flutes, Square End, 1/2" Cutting Length, 3/16" Cutting Diameter Feature
- Number of flutes varies; fewer flutes have more chip-carrying capacity and more flutes produce a finer finish
- Titanium carbon nitride (TiCN) coating lubricates the end mill for high-temperature stability and offers better abrasion resistance than TiN coating
- Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel
- Square nose end mills (also called square end) create sharp, unrounded cuts
- Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling
The Niagara Cutter SPC408 TiCN-coated cobalt steel square nose end mill has a 30-degree helix angle for milling a wide range of materials, including high-temperature alloys. The number of flutes varies; fewer flutes provide better chip-carrying capacity, while more flutes produce a finer finish. The TiCN coating offers increased hardness and greater abrasion resistance than uncoated or TiN-coated tools. The cobalt steel substrate can be run at faster speeds and stays sharp longer than high-speed steel tools, while offering greater resistance to heat and abrasion.
The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The tool’s square end has straight cutting edges that create sharp, unrounded cuts, while the center-cutting design has cutting teeth at the end of the tool that support making pocket cuts, profiling, and slotting. Cutting diameter tolerance is +0.001” to -0.000”. The end mill has a Weldon shank.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Monday, September 19, 2011
12mm High Speed Steel 4Fl SE End Mill - 3/8" Shank
12mm High Speed Steel 4Fl SE End Mill - 3/8" Shank Reviews
12mm High Speed Steel 4Fl SE End Mill - 3/8" Shank Feature
- Diam.: 12mm
- Shank: 3/8"
- Flute Length: 1"
- Overall Length: 2 11/16"
- Single End.
Friday, September 16, 2011
15/16" High Speed Steel St. Fl Hand Reamer
15/16" High Speed Steel St. Fl Hand Reamer Reviews
15/16" High Speed Steel St. Fl Hand Reamer Feature
- Size: 15/16"
- Overall Length: 10 1/4"
Tuesday, September 13, 2011
Niagara Cutter REM710 Cobalt Steel End Mill Set, Coarse-Pitch Roughing, TiN Coated, 4 Flutes, 6-piece
Niagara Cutter REM710 Cobalt Steel End Mill Set, Coarse-Pitch Roughing, TiN Coated, 4 Flutes, 6-piece Reviews
Niagara Cutter REM710 Cobalt Steel End Mill Set, Coarse-Pitch Roughing, TiN Coated, 4 Flutes, 6-piece Feature
- Roughing end mills have chip-breaking cutting edges that remove material in less time than conventional end mills
- Coarse-pitch tooth design is suitable for machining mild and cold-rolled steels
- Titanium nitride (TiN) is a general-purpose coating that combines high-temperature resistance and increased hardness compared to uncoated end mills
- Cobalt steel resists abrasion and high cutting temperatures, and has higher feed rates than high-speed steel
- Square nose end mills (also called square end) create sharp, unrounded cuts
Each Niagara Cutter REM710 TiN-coated cobalt steel coarse-pitch rougher end mill in this six-piece set has four flutes and a non-center-cutting design, and is suitable for machining mild and cold-rolled steels. The coarse-pitch tooth design has chip-breaking cutting edges that remove more material in less time than conventional end mills to support heavier cuts at higher speeds. The six-piece set includes one each of these cutting diameters: 3/16”, 1/4", 5/16”, 3/8”, 1/2", and 5/8”.
Each end mill has four flutes to optimize the feed and cut rate, and produces a rough finish that can be smoothed by a second finishing cut. The 30-degree helix angle balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action. The tool’s square end creates sharp, unrounded cuts, and has a chamfer end to strengthen the cutting edge. The non-center-cutting design is for applications such as peripheral milling.
Rougher end mills are special-purpose tools whose chip-breaking cutting edges create small chips for heavy cuts and remove more material in less time than conventional end mills, with minimal vibration (chatter). The general-purpose TiN coating combines stability at high temperatures with hardness for wear protection, increasing tool life and performance compared to uncoated end mills. The cobalt steel substrate can be run at faster speeds and stays sharp longer than high-speed steel tools, while offering resistance to heat and abrasion. Cutting diameter tolerance is +0.003” to -0.000". Each end mill has a Weldon shank.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Sunday, September 11, 2011
3/4" Carbide Tipped Boring Bar
3/4" Carbide Tipped Boring Bar Reviews
3/4" Carbide Tipped Boring Bar Feature
- Shank Diameter: 3/4"
- Overall Length: 3 1/8"
- Bore Depth: 1 1/8"
- Minimum Bore: 7/16"
- Alloy steel shanks.
Saturday, September 10, 2011
Niagara Cutter CD430 Carbide End Mill, General Purpose, TiN Coated, 4 Flutes, Double End, 3/8" Cutting Length, 1/8" Cutting Diameter
Niagara Cutter CD430 Carbide End Mill, General Purpose, TiN Coated, 4 Flutes, Double End, 3/8" Cutting Length, 1/8" Cutting Diameter Reviews
Niagara Cutter CD430 Carbide End Mill, General Purpose, TiN Coated, 4 Flutes, Double End, 3/8" Cutting Length, 1/8" Cutting Diameter Feature
- Four flutes produce a better finish than fewer flutes
- Double-end square nose end mills create sharp, unrounded cuts and have cutting edges on both ends for longer tool life
- Titanium nitride (TiN) is a general-purpose coating that combines high-temperature resistance and increased hardness compared to uncoated end mills
- Carbide can run at higher speeds than high-speed steel, resisting abrasion and high cutting temperatures
- Center-cutting design allows the end mill to plunge into material like a drill bit while also performing conventional surface milling
The Niagara Cutter CD430 TiN-coated carbide double end square nose end mill has four flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The double-end design has cutting edges on both ends, allowing a new cutting surface to be substituted when the first shows wear, which doubles the tool’s life compared to single-end square nose end mills. The tool’s square end has straight cutting edges that create sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. Four flutes produce a better finish than fewer flutes. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action.
The general-purpose TiN coating combines stability at high temperatures with hardness for wear protection, increasing tool life and performance compared to uncoated end mills. (TiN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. Cutting diameter tolerance is +0.000” to -0.002”. The round shank accommodates a variety of holders.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Subscribe to:
Posts (Atom)