1/16" 2Fl SE Carbide End Mill Reviews
Visit Store Now !!
Detail Products
Detail Reviews
Niagara Cutter SB335 Carbide End Mill, for Stainless Steel & Titanium, TiN Coated, 3 Flutes, Ball End, 3/4" Cutting Length, 7/32" Cutting Diameter Reviews
The Niagara Cutter SB335 TiN-coated carbide ball nose end mill has a 35-degree helix angle and three flutes for use on stainless steel, titanium, and high-temperature alloys. The 35-degree helix angle provides more support behind the cutting edge than higher angles, and increases cutting action and chip evacuation compared to the standard 30-degree helix. It efficiently cuts difficult-to-machine material, moving it up the spiral and away from the workpiece. The end mill’s three flutes provide better chip-carrying capacity than four flutes and a finer finish than two. They remove excess material from the cutting area and provide a third cutting edge to create an improved finish that may eliminate the need for a second finishing cut in some applications. The TiN coating combines stability at high temperatures with hardness for wear protection, increasing tool life and performance compared to uncoated end mills. The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life.
The tool’s center-cutting design allows the tool to plunge into the workpiece like a drill bit, while its ball end creates contoured surfaces where sharp edges are not required. It is best suited for slotting applications. The tool has an eccentric primary relief feature that provides better support behind the cutting edge than a flat relief, reducing tooth breakage in deep cuts. Cutting diameter tolerance is +0.000” to -0.002”. The tool’s round shank accommodates a range of tool holders.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Magnate EM1121 End Mills, 2-Flute MicroGrain Solid Carbide - 1/4" Mill Diameter; 1/4" Shank Diameter Reviews
Magnate EM1335 End Mills, 2-Flute MicroGrain Solid Carbide - 3/8" Mill Diameter; 3/8" Shank Diameter Reviews
3/4" Carbide Tipped Boring Bar Reviews
Niagara Cutter CD430 Carbide End Mill, General Purpose, TiN Coated, 4 Flutes, Double End, 3/8" Cutting Length, 1/8" Cutting Diameter Reviews
The Niagara Cutter CD430 TiN-coated carbide double end square nose end mill has four flutes and a 30-degree helix angle for general-purpose machining on a range of materials. The double-end design has cutting edges on both ends, allowing a new cutting surface to be substituted when the first shows wear, which doubles the tool’s life compared to single-end square nose end mills. The tool’s square end has straight cutting edges that create sharp, unrounded cuts, and the center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. Four flutes produce a better finish than fewer flutes. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles’ increased cutting action.
The general-purpose TiN coating combines stability at high temperatures with hardness for wear protection, increasing tool life and performance compared to uncoated end mills. (TiN is suitable for a range of materials, but TiCN or uncoated end mills are recommended for machining aluminum.) The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. Cutting diameter tolerance is +0.000” to -0.002”. The round shank accommodates a variety of holders.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Niagara Cutter MBZ215M Carbide Die/Mold End Mill, AlTiN Coated, 2 Flutes, Ball End, 1mm Cutting Length, 1mm Cutting Diameter Reviews
The Niagara Cutter MBZ215M metric AlTiN-coated carbide die/mold ball nose end mill has two flutes and a 15-degree slow helix for roughing and finishing complex three-dimensional dies and molds in extremely hard materials with a Rockwell Hardness of up to 62 HRC (hardened high-speed carbon and tool steels, for example). The 15-degree slow helix adds strength to the cutting edge and is optimized for machining the very hard materials used in die and mold manufacturing.
The AlTiN coating resists heat better than TiN, TiAlN, and TiCN coatings, increasing tool life and performance. It also offers increased hardness compared to TiN and may reduce the need for lubricants based on the application. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. The tool’s ball nose creates contoured surfaces, where sharp corners are not required. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. On smaller flute diameters (from 1 mm to 5 mm), the larger shank is blended to the smaller cutting edge with a 7-degree draft angle to minimize interference between the shank and the workpiece, allowing the tool to go further into recessed areas of the workpiece. The cutting diameter tolerance is +0.000 mm to -0.025 mm. The round shank accommodates a range of tool holders.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Niagara Cutter MB215 Carbide Die/Mold End Mill, AlTiN Coated, 2 Flutes, Ball End, 1/8" Cutting Length, 1/8" Cutting Diameter Reviews
The Niagara Cutter MB215 AlTiN-coated carbide die/mold ball nose end mill has two flutes and a 15-degree slow helix for roughing and finishing complex three-dimensional dies and molds in extremely hard materials with a Rockwell Hardness of up to 52 HRC (stainless steels, tool steels, and hardened steel alloys, for example). The 15-degree slow helix adds strength to the cutting edge and is optimized for machining the very hard materials used in die and mold manufacturing.
The AlTiN coating resists heat better than TiN, TiAlN, and TiCN coatings, increasing tool life and performance. It also offers increased hardness compared to TiN and may reduce the need for lubricants based on the application. The two flutes have better chip-carrying capacity than end mills with more flutes while offering additional support when the tool goes deep into the material in applications with a high depth of cut. The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. The tool’s ball nose creates contoured surfaces, where sharp corners are not required. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. On smaller flute diameters up to 3/16” the larger shank is blended to the smaller cutting edge with a 7-degree draft angle to minimize interference between the shank and the workpiece, allowing the tool to go further into recessed areas of the workpiece. The cutting diameter tolerance is +0.000” to -0.001”. The round shank accommodates a range of tool holders.
End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool’s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.
Niagara Cutter has been designing and manufacturing precision cutting tools since 1954. Specializing in end mills, cutting mills, and saws, the company is based in New York and manufactures its tools at facilities in Pennsylvania and Massachusetts. This allows the company control over production, from substrate to coating, which is essential for customers in a variety of industries, especially aerospace and automotive.
Magnate EM1518 End Mills - Ball Nose, MicroGrain Solid Carbide - 7/16" Mill Diameter Reviews
Magnate EM1116 End Mills, 2-Flute MicroGrain Solid Carbide - 11/64" Mill Diameter Reviews
3/32" 4Fl DE Carbide End Mill Reviews
Magnate EM1178 End Mills, 2-Flute MicroGrain Solid Carbide - 3.5mm Mill Diameter; 4mm Shank Diameter Reviews
7/16" 2Fl DE Carbide End Mill Reviews
